How to Replace a Tub
How to Replace a Tub
Blog Article
We've discovered this post involving Installing A Bathtub listed below on the web and thought it made good sense to relate it with you on this page.
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately challenging project. If the old tub is readily accessible, the task can relocate easily; if you need to open up a wall surface to remove the old bathtub and also position the new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually qualified yourself for the work as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is much better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your bathroom if you have actually currently purchased a brand-new bathtub and do not require to change the setup of your previous water system pipes.
Your devices as well as product checklist should consist of the following:
Preparing for the Installment
Firstly, the sustaining frame provided with the bath needs to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted access that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bathtub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if needed. Fill up the bath tub as well as also examine the overflow outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as explained in the supplier's user's manual. Tiling and securing around the bathtub needs to wait up until the bath tub has actually been used a minimum of once as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the faucet in place with the supplier provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type ought to be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Remember to constantly fill up the tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly offered on the market. It is advisable to fit the tiles making use of waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads on Installing A Bathtub, I assumed sharing that excerpt was a great idea. If you please take the time to share this blog posting if you appreciated it. Thanks a bunch for your time. Please check up our site back soon.
Visit Site Report this page